Cart 
Order Tracking
DY13 100W Power supply for RECI W2 / W4 CO2 SealedTube Laser Engraver Cutter Machine, 220V
Item Code: CS-PS-DY13-220V
Mark & model: DY13, small size, quick response, it is suitable for Reci W4 / S4 / W2 / S2 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power supply / power source adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power supply / power source makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the power supply / power source is not over the current limitation. Quality Report:
Ships to United States
4# 10mm Inner Diameter Silver Grommets Eyelets for ET10 Semi-automatic Grommet Machine
Item Code: CS-GM-WY-ET10
Description: • Iron material. • Inner Diameter: 10mm • Quantity/CTN: 10000pcs • Various colors: Silver • Applying grommet machine model: CS-SGM-WY-ET10 • Widely used for Flex Banner, mesh, and other advertising materials. Warm Tips: This Grommets can not apply to
Ships to United States
Small Size Pneumatic Bending Slot Cutting Machine Tools for Metal Channel Letters
Item Code: CS-HD-BC02
Processing Material: Aluminum, Iron, Steel, Acrylic, PVC Max Cutting Width: 15cm (5.9") Max Cutting Thickness: Adjustable & No limited Cutting Way: 90 degree & V-Cutting Working Air Pressure: 0.6Mpa Note: 1. The knife plate for slotted flat coil is provided with the device 2. For grooving profiles coil, please purchase below items via this link: /products/14467/100mm 3.9 quot diameter saw blade cutting blade cut aluminum acrylic pvc.html Details: Applications:
Ships to United States
Ving 300W 95L Portable Acrylic Polishing Machine, Oxygen Hydrogen Flame Generator 2 Gas Torches free, 220V
Item Code: APM-H180B-220V
Note: Please clean the new machine when using it for the first time. Cleaning method: put the electrolyte into the machine, take out the electrolyte after running for 3-5 hours, and then add the electrolyte again. Description: • Synthetic glass (acrylic) polishing, Oxy - hydrogen generator is
Ships to United States
1000pcs 32mm Blank Pin Badge Button Supplies for Badge Maker Machine
Item Code: CS-CO-32
Description: Round size: 1-1/4" (32mm) Upper-shell: Chrome ABS mylar disc / Iron Metal Bottom The component contains: Upper-shell, Down-shell, Film, Pin Qty/CTN: 1000pcs The item contains: Upper-shell: 1000pcs Down-shell ABS / Iron Metal: 1000pcs Film: 1000pcs Pin: 1000pcs Application:
Ships to United States
25.6" x 35" (650mm x 900mm) High Precision AD CNC Engraver Machine
Item Code: CNCR-CP-6590
CNCR-CP-Y series engraving machine, is released for the sign advertising industry with a high performance / cost ratio. It has a new look, fast speed and high precision. It comes with DSC control system, HD LCD screen, and friendly interface. Main Configuration Information: Engraving Area:
Ships to United States
1000pcs 37mm Blank Pin Badge Button Supplies for Badge Maker Machine
Item Code: CS-CO-37
Description: Round size: 1-9/20" (37mm) Upper-shell: Chrome ABS mylar disc/ Iron Metal Bottom The component contains: Upper-shell, Down-shell, Film, Pin Qty/CTN: 1000pcs The item contains: Upper-shell: 1000pcs Down-shell ABS / Iron Metal: 1000pcs Film: 1000pcs Pin: 1000pcs
Ships to United States
CALCA 20W Split Fiber Laser Marking Machine, Raycus Laser & Rotation Axis, FDA
Item Code: LMM-F-20W-S
CALCA 20W Split Fiber Laser Marking Machine, Raycus Laser & Rotation Axis, FDA The machine equip with software. Fiber Laser Marking Machine mainly consists of four parts: fiber laser, galvanometer scanning system, computer control system and the worktable. Name Origin (brand
Ships to United States
1000pcs 50 x 50mm Square Pin Badge Button Supplies for Badge Maker Machine
Item Code: CS-CO-55F
Description: Size: 50 x 50mm Upper-shell: Chrome Bottom-shell: ABS mylar disc The component contains: Upper-shell, Down-shell, Film, Pin Qty/CTN: 1000pcs Packing Size: 33 x 22 x 5cm (13 x 8.6 x 1.9in) The item contains: Upper-shell: 1000pcs Down-shell ABS: 1000pcs Film: 1000pcs Pin: 1000pcs
Ships to United States
2 in 1 Auto-open Cap and Label Heat Press Machine
Item Code: HTM-CP2815S
Steps: ①Print iamge on paper. ②Stick the image with thermal tape. ③Put the subject on the working table. ④Adjust suitable pressure . ⑤When the heating board reach temp you have set,close the Handle (3), the machine will sound an alarm automatically when reaching time,machine will open automaticly
Ships to United States
Ving Automatic Channel Letter Bending Machine with Slotting, Notching and Flanging Functions
Item Code: MBM-TPS-S1800
Bending tool quick-change system: In order to get high quality bending for different material, TPS company researched and developed bending tool quick-change system to realize independent quick change for slotting and bending for plate metal material and notching and flanging for flat aluminum material to ensure high accuracy bending for two different processing types. Functions for processing different material: It can bend aluminum coil max. width 180mm, max. 1mm thickness with slotting, notching and flanging function. More tool rod bending system: On the basis of alternating double bending bars system, it increases one bending bar for notching of aluminum flat material. It can realize function types changing freely between slotting and bending for flat material and notching, flanging and bending for aluminum flat material. Bending forming degree is greatly increased. Reel type feeding: The front roller flattening mechanism, it can flatten materials effectively in advance, to avoid jam due to uneven materials. Alternating clamping feeding mechanism: The alternating clamping feeding mechanism with large torque, high precision and high speed transmission performance is driven with double screw rods and positioning nuts, and controlled by servo motor to ensure real material feeding accuracy to ±0.1mm. It solves problems of slipping and independent of roller pressure feeding type. Servo motor control notching and flanging mechanism: It uses servo motor to control notching mechanism with characters of smaller size, higher speed, more stable property, without oil contamination and low noise comparing with hydraumatic notching. Functions for processing different material: It can bend aluminum coil max. width 180mm, max. 1mm thickness with slotting, notching and flanging function. Processing stainless steel material Processing aluminum coil material Software support DXF/PLT file in，support CAD、TYPE3、CRELDRAW、ILLUSTRATOR,etc.
Ships to United States
4# (10.5mm) Silver Iron Grommet for Mini Hand Press Grommet Machine
Item Code: CS-GM-ZG-S4
Description: • Iron material. • Inner Diameter: 10.5mm • Outer Diameter: 18mm • Height: 6mm • Quantity/Parcel: 500pcs • Various colors: Silver • Two parts: grommet and washer • Applying grommet machine model: CS-MGM-ZG and CS-MGM-ZG-FS. Warm Tips
Ships to United States
DY13 100W Power supply for RECI W2 / W4 CO2 SealedTube Laser Engraver Cutter Machine, 110V
Item Code: CS-PS-DY13-110V
Mark & model: DY13, small size, quick response, it is suitable for Reci W4 / S4 / W2 / S2 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power supply / power source adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power supply / power source makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 110V, 60Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the power supply / power source is not over the current limitation. Quality Report:
Ships to United States
4#(10mm)Silver Iron Grommet for Heavy Duty Hand Press Grommet Machine
Item Code: CS-GM-WD-S4
Description: • Iron material. • Inner Diameter: 10mm • Outer Diameter: 19mm • Various colors: Silver • Two parts: grommet and washer • Qty/CTN: 20,000pcs/carton • Applying grommet machine model: CS-MGM-SD, CS-MGM-SD-F1, CS-MGM-SD-F2. • Widely used for flex
Ships to United States
DY20 150W Power supply for RECI W6 / W8 CO2 SealedTube Laser Engraver Cutter Machine, 110V
Item Code: CS-PS-DY20-110V
Mark & model: DY20, small size, quick response, it is suitable for Reci W6 /W8 / S6 / S8 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power sourcesupply adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power sourcesupply makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the power supply / power source is not over the current limitation. Quality Report:
Ships to United States
DY10 80W Power supply for RECI W1 CO2 SealedTube Laser Engraver Cutter Machine, 110V
Item Code: CS-PS-DY10-110V
Mark & model: DY10, small size, quick response, it is suitable for Reci W2 / S2 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power supply / power source adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power supply / power source makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2/S2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 110V, 60Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the supply / power source is not over the current limitation. Quality Report:
Ships to United States
10mm Inner Diameter Tan Grommet Eyelets for Semi-automatic Grommet Machine
Item Code: CS-GM-JN-S10
Description: Iron material. Inner Diameter: 10mm Outer Diameter: 16mm Height: 5mm Quantity/CTN: 20000pcs Various colors: Tan Type: only grommet no need washer Applying grommet machine model: CS-GM-JN-DKJ Mould machine can change the corresponding to the other. Warm Tips: This Grommets can not
Ships to United States
6#(14mm)Silver Iron Grommet for Heavy Duty Hand Press Grommet Machine
Item Code: CS-GM-WD-S6
Description: • Iron material. • Inner Diameter: 14mm • Outer Diameter: 23mm • Various colors: Silver • Two parts: grommet and washer • Qty/CTN: 20,000pcs/carton • Applying grommet machine model: CS-MGM-SD, CS-MGM-SD-F1, CS-MGM-SD-F2. • Widely used for flex
Ships to United States
10.4mm Inner Diameter Silver Iron Grommet Eyelets for Automatic Grommet Machine
Item Code: CS-GM-ST104
Description: Iron material, and the washer is ABS Inner Diameter: 10.4mm Outer Diameter: 18.5mm Package: 1500pcs/bag, 10bags/carton Various colors: Silver Applying grommet machine model: CS-AGM-ST104 Mould machine can change the corresponding to the other. Warm Tips: This Grommets can not
Ships to United States
DY10 80W Power supply for RECI W1 CO2 SealedTube Laser Engraver Cutter Machine, 220V
Item Code: CS-PS-DY10-220V
Mark & model: DY10, small size, quick response, it is suitable for Reci W2/S2 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power supply / power source adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power supply / power source makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2/S2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the supply / power source is not over the current limitation. Quality Report:
Ships to United States
13mm Inner Diameter Silver Iron Grommet Eyelets for Automatic Grommet Machine
Item Code: CS-GM-ST13
Description: Inner Diameter: 13mm Outer Diameter: 21.5mm Package: 1000pcs/bag, 10bags/carton Various colors: Silver Iron material, and the washer is ABS Applying grommet machine model: CS-AGM-ST13 Mould machine can change the corresponding to the other. Warm Tips: This Grommets can not apply
Ships to United States
4#(10mm)Golden Iron Grommet for Heavy Duty Hand Press Grommet Machine
Item Code: CS-GM-WD-G4
Description: • Iron material. • Inner Diameter: 10mm • Outer Diameter: 19mm • Various colors: Golden • Two parts: grommet and washer • Qty/CTN: 20,000pcs/carton • Applying grommet machine model: CS-MGM-SD, CS-MGM-SD-F1, CS-MGM-SD-F2. • Widely used for flex
Ships to United States
DY20 150W Power supply for RECI W6 / W8 CO2 SealedTube Laser Engraver Cutter Machine, 220V
Item Code: CS-PS-DY20-220V
Mark & model: DY20, small size, quick response, it is suitable for Reci W6 / W8 / S6 / S8 laser tube. Original: Asia and Pacific Area China Quality standard: International H.S. Classification: Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts. Warm tips: The power supply is to be used for Reci, EFR and WEEGIANT laser tube. If you want to make it work on other brands, please check the specification before order. Features: This power sourcesupply adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube. The power sourcesupply makes laser tube output larger and more stable. Quick Response: It can enlarge laser power and prolong laser tube‘s service life. Easy Control: The start and stop of laser can be easily controlled by TTL level. This power supply / power source has output open circuit protection. This power supply / power source has TTL signal indication, water through signal indication and laser output indication. This power supply / power source has the BUTTON to test it work properly. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc We stick the protection film on the power source to prevent the metal parts of the scrape! I. Instruction for sub - connection wire of the control end 1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA. 2) TH. TL refers to high and low power level respectively, and WP refers to water protection. 3) Footer 5 G refers to ground and 6 refers to input end. 4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. 5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K. 6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. 7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. 8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. 9) The model is applicable to Z2 laser, it is necessary to regulate and use the current according to the laser instructions. 10) The ammeter is concatenated to the cathode line. II. Instruction for power wire Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation. III. Instruction for laser connection wire 1) The positive red - line with high voltage is connected to the laser tail 2) The negative white - line is connected to laser output window IV. Current limitation To limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery. V. Linear scale between input signal and the output current Turn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA. Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal. VI. Using current The use standard for our power supply / power source is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by the power supply / power source is not over the current limitation. Quality Report:
Ships to United States
